The cut decides which face of the log you end up walking on. Plain sawn boards show cathedral arches, rift sawn boards show tight, straight lines, and quartersawn flooring shows straight grain with flecks in oak. The cut also changes how a board moves with humidity, so it is a performance choice as well as a style choice.
What the three cuts actually are
All three come from the same tree. The difference is the angle between the growth rings and the face of the board.
- Plain sawn: the log is sliced in parallel passes. The rings meet the face at a shallow angle, typically under 30 degrees. This is the most common cut, and it gets the most boards from a log.
- Quartersawn: the log is split into quarters, then cut so the rings meet the face at roughly 60 to 90 degrees.
- Rift sawn: the angle falls in between, typically 30 to 60 degrees. The result is the straightest, most uniform grain of the three.
Those angles are typical ranges. Mills draw the lines a little differently, so two suppliers may not match exactly.
How each cut looks on the floor
Plain sawn
This is the grain most people picture. You see long arches, often called cathedrals, with a lot of variation from board to board. The pattern is lively. It also tends to hide small scuffs and dust better than a clean, straight pattern.
Quartersawn
The grain runs in tight parallel stripes. In white oak, the rays are cut across and show up as flecks that shimmer as light moves across the room. The effect is strongest in white oak and subtler in many other species. If you like a traditional, crafted look, this is the one.
Rift sawn
Rift is the calm option. The lines are straight and even, and there is little or no fleck. It reads as modern and quiet, and it takes stain evenly. Many homeowners who ask for “straight grain” really want rift.
One warning when you shop. Products sold as “rift and quartered” are often a mix of both cuts. Ask to see a full box laid out, not a single hand-picked board, so the room does not surprise you.
How the cut changes the way boards move
Wood moves mostly across its width, not its length. How much it moves depends on how the rings are oriented. Plain sawn boards typically swell and shrink more across the width. Quartersawn and rift boards tend to move less across the width, so they often cup less and show smaller seasonal gaps.
That matters in Atlanta. Summers are humid, and a heated house in January can run very dry. Follow the flooring manufacturer’s stated humidity range (commonly around 30 to 50 percent) and hold it as steadily as you can. Our post on how Atlanta humidity changes hardwood floors by season covers what to expect through the year.
Width multiplies the effect. A 3-inch board has less room to move than a 7-inch board. A wide plain sawn plank is the cut most likely to cup in a damp year. Homeowners in Alpharetta ask us about this often, usually when they want wide boards across an open floor plan.
None of this makes quartersawn or rift sawn boards immune. A plumbing leak or a wet crawl space will damage any cut. Radiant heat is its own question, and we cover it in radiant heat under hardwood.
Other things that change the choice
- Availability. Rift and quartered cuts yield less per log, so species, widths and lead times can be narrower. Ask early.
- Species. Fleck is most dramatic in white oak. If species is still open, read white oak vs red oak first.
- Grade. Grade is a separate decision from the cut. A rustic grade shows knots and color swings whatever the grain angle. See hardwood grades.
- Finish. A natural or light finish shows fleck and grain clearly. Dark stain often hides much of it.
- Direction. Straight grain emphasizes the lay of the boards. Our guide to wood flooring direction explains how layout reads in a room.
- Refinishing. Solid boards of any cut can be sanded and refinished. With engineered boards, the top wood layer sets the limit. See our hardwood floor restoration service for what that looks like in practice.
A decision sequence: check this first, then this
- Look at the moisture picture. Is the home over a slab, a crawl space or a basement? Does the HVAC hold steady humidity? Big swings point toward rift or quartered.
- Pick the width. Boards over about 5 inches move more in absolute terms. Wide plank in plain sawn needs the most careful humidity control.
- Decide the look. Arches and variety mean plain sawn. Straight and calm means rift. Straight with shimmer means quartersawn.
- Choose the species. Then look at a full sample box of that species and cut in your own room’s light, morning and evening.
- Confirm supply. Ask about lead time and whether the product is a pure cut or a rift and quartered mix.
- Plan the finish. Sheen and stain change how much grain shows. Test on an offcut, not a catalog photo.
- Match the install method to the subfloor. Nail-down, glue-down and floating each behave differently. Our comparison of installation methods explains the trade-offs.
Before any of it goes down, acclimate the wood per the manufacturer’s instructions. Keep it in the house until its moisture readings are within the specified difference of the subfloor, and don’t go by a set number of days. Our hardwood flooring installation and broader flooring installation work both start with that check. For a wider overview of the material choice, see how to choose new wood flooring.
If you are weighing these cuts for a room, we can bring samples to your home and talk through it. Atlanta Floor One has served the north Atlanta suburbs since 2008. Request a free estimate or call 404-578-0926.
Frequently asked questions
Usually, yes. Quartersawn boards tend to swell and shrink less across their width, so they often cup less and show smaller seasonal gaps. They still react to moisture, so humidity control and proper acclimation matter for every cut.
Both have straight grain, but the growth rings meet the board face at different angles. Quartersawn runs at roughly 60 to 90 degrees and shows ray fleck in oak. Rift runs at roughly 30 to 60 degrees and looks more uniform, with little or no fleck.
White oak has ribbon-like rays that run from the center of the tree outward. When a board is cut across them, they show up as shimmering flecks on the face. Cutting at a rift angle avoids most of them.
Yes. If the boards are solid, the cut does not change how they are sanded and refinished. With engineered boards, the thickness of the top wood layer sets how much sanding is possible.
No. Plain sawn is the same species and can be the same grade as the other cuts. It simply has a different, more varied grain pattern and moves a little more with humidity.
Keep reading
- Top Advantages of Choosing White Oak Hardwood Flooring
- Top Hardwood Flooring Trends to Look for in 2020
- What to Look for in a Good Hardwood Flooring Contractor

