How Flat Does a Subfloor Need to Be for New Flooring?

Sunlit living room with smooth wide-plank oak flooring, a linen sofa, a low wood coffee table, built-in shelves with ceramic

The short answer on subfloor flatness: most new floors need the surface to stay within about 3/16 inch over 10 feet, or roughly 1/8 inch over 6 feet. Large tile often asks for tighter. If your subfloor falls outside that range, it should be corrected before any flooring goes down, not after.

Flat Is Not the Same as Level

People mix these up. Installers do not. A level floor sits true to horizontal. A flat floor has no local humps or dips.

A floor can slope an inch across a room and still be flat. It can also be level at the walls and have a belly in the middle. New flooring cares about flat. A gentle slope rarely hurts a plank. A hump or dip over a few feet does, because the plank has to bridge it or bend into it.

Many older homes in north Atlanta have some slope from settled framing. We can usually work with that. The humps and dips are what we fix.

How Much Variation Each Floor Tolerates

The numbers below are typical. Every product has its own limit, so we read the instructions for the floor actually going in.

Floor typeTypical flatness limitWhat shows when it is too uneven
Nail-down solid hardwood3/16 inch in 10 feetSqueaks, hollow spots, boards pulled tight into dips
Floating engineered wood3/16 inch in 10 feetBounce, stressed joints, seams that separate
Luxury vinyl plank3/16 inch in 10 feet, sometimes tighterRidges telegraphing through, lifted ends, open seams
Large-format tileOften 1/8 inch in 10 feetUneven tile edges, cracked tile or grout
CarpetMost forgivingBumps and screw heads can still show through

The method matters too. Floating floors bridge low spots instead of following them, so the joints flex. Nail-down boards get pulled into dips, which leaves hollow spots. Glue-down floors copy whatever is under them. Our post on nail-down vs glue-down vs floating floors explains how each one behaves.

How We Check a Subfloor

You can do a rough version yourself. You need a straightedge 6 to 10 feet long, a pencil and a flashlight. Work in this order:

  1. Clear and sweep. A pebble or a screw head will fool the straightedge.
  2. Lay the straightedge down in many spots. Try along the walls, across the middle and on diagonals.
  3. Look for light and rocking. Light under the edge means a dip. Rocking means a hump.
  4. Measure the gap at its widest point with a tape.
  5. Mark it. Circle high spots and outline low spots in pencil so you have a map.
  6. Look for the cause. Squeaks, loose panels, soft spots or a damp smell point to a problem bigger than flatness. Handle that first, as covered in our subfloor repair guide.

Fixing High Spots and Low Spots

The fix depends on what the subfloor is made of and how far off it sits.

  • Humps on plywood or OSB. Raised panel seams and ridges are often sanded or planed down. Loose panels get screwed tight to the joists first.
  • Dips on a wood subfloor. Shallow dips take a feathered patching compound. Broader low areas may need a leveling layer.
  • Humps on concrete. These are ground down.
  • Dips on concrete. Self-leveling compound is poured over a primer and finds its own level. It is often walkable in a few hours, but many products need a day or more before flooring goes over them.
  • A sag across several feet. This usually points to framing. It is repaired from below, not covered from above.

One common shortcut does not work. Thin underlayment follows the surface under it, so it will not flatten anything. Our post on underlayment under luxury vinyl plank covers what it is actually for.

What Goes Wrong When Prep Is Skipped

These are the failures we see most. They often appear within the first season, once furniture and foot traffic settle the floor.

  • Squeaks and a hollow sound over dips in nail-down wood.
  • Click-lock joints that pop or open where a plank spans a low spot.
  • Ridges, seams and screw heads showing through vinyl plank.
  • Tile edges that sit proud of each other, with cracked grout lines.
  • Planks that rock at the ends and wear unevenly.

Every one of these is cheaper to prevent than to tear out. That is why we check flatness before we talk about the finished look.

Where This Comes Up in Our Area

Homeowners in Alpharetta and nearby suburbs ask us about this most when old carpet or tile comes up and the subfloor underneath is not what they expected. Tile removal often leaves ridges and adhesive. Houses over crawl spaces can have sagging joists. Slab floors can have dips from the original pour.

If you are planning hardwood flooring or luxury vinyl plank, ask for the subfloor to be checked before you pick a product. Tile work is stricter still, so bathroom and kitchen projects under tile and bathroom remodeling get the tightest check. If you just bought a house, our new home flooring checklist shows where this step fits.

Not sure what is under your old floor? Atlanta Floor One has been licensed, insured and working across the north Atlanta suburbs since 2008. Request a free estimate or call 404-578-0926, and we will check the subfloor before anything else.

Frequently asked questions

What is the flatness tolerance for a subfloor?

For most wood, engineered and vinyl plank floors, the subfloor should typically stay within 3/16 inch over 10 feet, or about 1/8 inch over 6 feet. Large tile often needs it tighter, so the instructions for the specific product decide.

Can underlayment fix an uneven subfloor?

No. Thin underlayment follows the surface under it, so humps and dips stay. The subfloor has to be sanded, patched or leveled first.

Does my floor have to be level, or just flat?

Flat matters far more. A floor can slope gently across a room and still take new flooring well, while a hump or dip over a few feet causes problems.

How long does self-leveling compound take before flooring can go down?

It is often walkable in a few hours, but many products need a day or more before flooring goes over them, especially when poured thick. Follow the instructions for the exact product.

Keep reading