New Home Flooring Checklist: Do This Before Furniture

Bright, elegant furnished living room with wide-plank oak floors in a satin finish, a linen sofa, a wool area rug, a wooden s

The best new home flooring checklist is short. Walk every room while it is empty, check for moisture and soft spots, decide what to keep or replace, and finish floor work before the furniture arrives. An empty house lets us sand, install, and let finishes dry without moving a single bed. Once the boxes are in, every one of those steps gets slower.

Why the empty house is your best window

Floors are easiest to judge when nothing sits on them. Side light from a window shows dips, ridges, and scratches. Furniture and rugs hide all three.

A common situation: the closing is done, the movers are booked, and nobody has looked closely at the floors. If you do the walkthrough first, you learn what you have. If you wait, you learn it piece by piece, usually after a stain or a squeak shows up in a full room.

Installing and refinishing are also simpler in an empty room. Nothing has to be stacked in the hallway, and the crew can work from wall to wall. We handle flooring installation in Alpharetta and the nearby north Atlanta suburbs, and the houses where floors were done before move-in are the easiest to plan.

Five questions, in this order

Resolve moisture and structural problems first. If the floor is not dry, solid, and flat, settle that before anything else, because the later questions depend on it. The last two questions are decisions, not pass-or-fail gates, so work through them even if the answer is not a clean yes.

  1. Is it dry? Dark stains near the dishwasher, toilets, tubs, water heater, or exterior doors need a look first. So does a musty smell, or any board with edges higher than its center. Find the source of the water before you plan anything else.
  2. Is it solid? Walk each room slowly and listen. A squeak often means a loose fastener. A spongy feel means the subfloor itself may be damaged. Our subfloor repair guide explains what to fix, what to replace, and what to leave alone.
  3. Is it flat? Lay a long straight board or level across the floor. Many wood installations want a subfloor flat to roughly 3/16 inch over 10 feet, and some products ask for tighter. Dips and high spots show through new flooring.
  4. Is it right for how you live? Think about pets, kids, afternoon sun, and the entry from the garage. Material follows from that. Our post on choosing the right flooring for your home walks through the tradeoffs.
  5. Is it worth keeping? Lift a corner of carpet in a closet to see what is underneath. Solid wood boards suggest hardwood that may be refinishable. Plywood or OSB sheets usually suggest there is no finish hardwood under the carpet, but they can also be an underlayment laid over older hardwood. Visible plank boards can also be a plank subfloor, not finish hardwood. Have a pro check the wood’s type, thickness, and condition before you decide.

What the floor is telling you

This is how we read common signs on a walkthrough. These are patterns, not diagnoses. A floor still needs to be seen in person.

What you seeWhat it often meansTypical next step
Dark spots near a dishwasher, toilet, or tubA past or ongoing leakFind the source, then probe the subfloor for soft spots
Board edges higher than the centersMoisture from below or an old leakConfirm the floor is dry before any sanding or new flooring
Squeaks in one areaLoose subfloor or fastenersRe-fasten before new flooring goes over it
Carpet that smells after cleaningA soaked pad, maybe a stained subfloorPull a corner and check the pad and the wood beneath
Hairline gaps between boards in winterSeasonal movementUsually leave alone; they often close in humid months
Hollow sound when you tap tileA loose bond to the floorMark it and check nearby tiles, since loose ones often cluster

Moisture decides what you can install

Wood moves with humidity. Indoors, most hardwood is happiest at roughly 35 to 55 percent relative humidity. A basic hygrometer will tell you where your house sits. A home that sat empty with the system off can be well outside that range.

Concrete slabs and basements need moisture testing before any wood or vinyl goes over them. Slabs release moisture slowly. Wood laid over a damp slab tends to cup, and glued floors can fail at the seams or edges.

If the house has a crawl space, look at it too. Damp air below reaches wood floors through the subfloor. Fixing that is far easier before the new floor is down than after.

Decide room by room: keep, refinish, or replace

You do not need one answer for the whole house. Bedrooms, the kitchen, and the entry often call for different decisions.

  • Keep: the floor is solid, flat, and dry, with ordinary wear. Add felt pads and move on.
  • Refinish: solid hardwood with a dull finish and surface scratches. A full refinish typically means three sanding passes, often from around 36 or 40 grit up to 80 or 100, then two to three coats of finish. That is the work behind our hardwood floor refinishing service.
  • Replace: a soft subfloor, deep pet damage, boards sanded too thin, or a patchwork of mismatched repairs. Our guide on how to choose new wood flooring helps with that decision. Our flooring installation crew handles most common materials, including hardwood, engineered wood, vinyl plank, and tile.

One caution for older houses. Do not sand or tear up old vinyl tile or its black adhesive until it has been tested. Leave that material alone until you know what it is.

Sequence the work, then the move-in

Do the dusty work first. Painting, drywall repair, and ceiling work come before floors, because dust and drips are hard on a fresh finish. Small trim touch-ups come after.

For a few rooms, a refinish often runs three to five days including coats. With a water-based finish, people can typically walk on the floor in socks after about a day. Furniture often goes back after two to three days. Rugs wait longer, often about two weeks.

Fresh finish and adhesive both have a smell for a while. We cover how long in our post on why a new floor smells and how long it lasts.

When furniture does go in, lift it. Do not drag it. Put felt pads on every leg before it touches the floor.

Stairs and the spots people forget

Stairs take the worst of move-in day. Boxes, dollies, and heavy furniture all scrape the treads. If they look tired, stair refinishing is often enough when the structure is sound. If the railings, risers, or stringers need to change, that is a stair remodeling job. Either one is far easier before the house is full.

Also check closets, the laundry room, the pantry, and the spot where the refrigerator sits. Old leaks like to hide in those places. Look at the garage entry too, where grit and moisture come in every day.

If you are about to close, or just did, we are glad to walk the house with you before the movers come. Request a free estimate on our contact page or call 404-578-0926.

Frequently asked questions

Should I do floors before or after I move into a new house?

Before, whenever you can. An empty house lets the crew work wall to wall and lets finishes dry without anything stacked in the way. Moving furniture out of finished rooms later is slower and adds risk to the floor.

How soon can furniture go back after a hardwood floor is refinished?

With a water-based finish, furniture often goes back after about two to three days, and rugs usually wait longer. The exact timing depends on the finish and the humidity, so follow your installer’s instructions.

How can I tell if there is hardwood under my carpet?

Lift a corner of carpet inside a closet, or remove a floor vent cover and look at the edge of the floor. Plywood or OSB sheets usually suggest there is no hardwood underneath, though they can also be laid over older hardwood, and visible plank boards can be a plank subfloor rather than finish hardwood. A pro should confirm what you have, and its thickness and condition, before you plan on refinishing it.

Keep reading